Search Results

Among the problems before the designers of plowing tractors, none is more important than that of ascertaining the most economical plowing speed at which to operate a tractor to give first-class work at a minimum cost. The solution must be right from both the maunfacturer's and the farmer's standpoints. A variety of soil resistances, different speeds, widths and depth of cut, types and shapes of plows must be considered. The recently published draft data of Professor Davidson of Iowa State College and those of the Kansas State Agricultural College are used. They indicate in general that in each kind of soil, whether heavy or light, with speed increase there is a corresponding increase of draft, the amount of which is dependent upon the speed, shape of plow and nature of soil. The further experiments made relative to increased speed and draft and to the area plowed at different speeds are described and discussed, the results being shown by charts.

The annual report covering transportation by the largest British air-transport company laid particular emphasis upon the greater value of the faster machines in its service. Granted that efficient loads can be carried, the expense, trouble and danger of the airplane are justified only when a load is carried at far greater speed than by any other means. A reasonable conclusion seems to be that we can judge the progress made in aviation largely by the increased speed attainable. It is interesting and possibly very valuable therefore to inquire into the relations of power and resistance as applied to small racing machines with aircraft engines that are available.

A tendency exists in most shops to assume that brazed joints cannot be successfully heat-treated. As a consequence, many fittings used in aircraft work and assembled by brazing smaller parts together are finished and installed without being heat-treated after the brazing operation. This practice causes parts to be used that not only do not develop the available strength of the material, but which are in some cases, under internal stress due to the heating in the brazing operation. Recent experiments made at the Naval Aircraft Factory show that the assumption mentioned is entirely erroneous. The author considers this matter with a view to specifying the use of steels and brazing spelters which will permit the subsequent or perhaps the simultaneous heat-treatment of the parts.

Stating the desirability of reducing unsprung weight in motor vehicles as a recognized fact and that 75 of 100 engineers interviewed favor such reduction, the particular advantages resulting are given as improved riding qualities, economy in tire wear and better acceleration. Mathematical deductions to establish the most desirable ratio of sprung to unsprung weight are not attempted, the intention being rather to state the reasons favoring lighter wheels and axles. Unsprung weight effects depend primarily upon the ratio of sprung to unsprung weight. No data determining the most desirable ratio are available, but an investigation of the proportional weight of the unsprung and sprung parts of good-riding-quality automobiles showed it to be about 1 to 3. By constructing the wheels and the axles of light metal it is possible to maintain such a ratio, assure good riding qualities and reduce the total weight.

The paper treats the subject of ability from the point of view of its relation to the present trend in motor-truck design, setting forth some of the fundamental considerations involved. An ability formula when applied to automotive vehicles is to determine a “factor of experience” from which engine sizes and gear ratios can be calculated. While passenger-car performance is measured in terms of speed and acceleration, the latter are not the most important considerations in motor trucks, the speed of which is limited by the use of a governor. Wind resistance also is negligible at truck speeds. Practically the only resistances to be overcome by a motor truck are road friction and the force of gravity. Both road and grade resistance are in direct proportion to weight carried and are usually expressed in terms of pounds per pound.

THE design of a modification of the Class B Government standardized truck engine is presented, the principal object being a saving in weight without sacrificing either durability or safety factors. The crankcase design is rigid, but the metal is distributed so that the weight will be a minimum. The crankshafts are made of chrome-nickel steel of an elastic limit of 120,000 lb. per sq. in., which further carries out the idea of durability with low weight. The connecting-rod length is slightly more than twice that of the stroke, and this, with light-weight pistons, obviates vibration, without adding weight to the engine on account of increased cylinder height. The flywheel and bell-housing diameters were selected with a view to securing enough flywheel weight for smooth running without increasing the engine weight materially. All-steel supports reduce breakage of arms to a minimum. The manifolds are carefully designed to give economical performance, even with low-grade fuels.

The author discusses the different types of material used in the production of the Liberty engine, the physical properties of the finished parts and the heat-treatments used in making them, applying the information as set forth to the automobile, truck and tractor industries. Under their several heads the different engine pans are discussed with close attention to details. Chemical analyses are given for each part and approved heat-treating temperatures are indicated. Quenching, direct and indirect, water and oil cooling, hard spots, warpage, scaling and hair-line seams are treated. The advantages and disadvantages of the Izod impact test are stated briefly.

In the past the majority of trucks have been equipped with wood wheels. These gave good service, but the results demanded under strenuous modern conditions seem, the author states, to make the substitution of steel wheels on medium and heavy-duty trucks imperative. Truck engineers and builders seem to recognize the fact, but to hesitate to make the change, chiefly because a metal wheel is somewhat higher in first cost and because some designs have not as yet rendered the service expected of them. The service return of metal wheels is given from the records and reports of the London General Omnibus Co. and the Fifth Avenue Coach Co., both of which use steel wheels exclusively. The added mileage is in excess of wood-wheel service and exceptional tire mileage is shown. The author states briefly the arguments for the hollow-spoke, hollow-rim, the hollow full-flaring spoke and the integral-hub metal wheels.

Iron rust is caused by electrolytic action between the various constituents of iron or steel in the presence of moisture and impurities. It is a continuous process; a coating of rust does not protect the metal underneath. The principal requirements of a rust-prevention process as applied to automobiles, aircraft and other machined and hardened parts are that it (1) Prevent rusting under normal use (2) Prevent the spreading of rust (3) Make no change in dimensions or fits (4) Make no alterations in physical properties (5) Be permanent for the life of the part (6) Be easy and quick of application (7) Be commercially practicable as to cost Of the most familiar rust-proofing processes, the cold, the hot and the high-temperature, the last is eliminated by requirements (3) and (4), while the cold processes and also japanning are eliminated by (2), (3) and (5). There remain three hot processes, the Parker, the Coslett and the Guerini.

Airships were not generally considered important before the war. Many thought they would never become practical as a means of transportation. The proper conception of what an airship is having first been explained, the three principal ways in which progress has been made are specified as weight-saving, improvement of overall propulsion efficiency and decreasing resistance and increase in size. The last mentioned feature is discussed in some detail, the conclusion being that practically anything is possible, given an airship of sufficient size. The future needs of airship development are then considered, such as more suitable engines, multiple powerplants, dependability, the development of better fabric and better landing and hangar facilities.

Starting with the statement that command of the air in warfare rests largely with the side that produces the best single-seater fighter, the author proceeds to outline some of the problems confronting the designer of fighting airplanes, and particularly the smaller ones. Considering better performance and better fighting qualities as the main desiderata, the author discusses means of obtaining them by: (1) increasing the horsepower-weight ratio; (2) decreasing the wing or structure resistances; (3) devising a new arrangement of the supporting planes, with regard to the position of pilot or crew, or by a combination of the above. Considerable space is devoted to methods of decreasing wing resistance, principally by employing low-resistance aerofoils, and the shaping of wing tips is also referred to.

The author outlines methods for producing high-speed engines with high mean effective pressure and gives data resulting from several years' experimental work. He discusses the desirable stroke-bore ratios; valve area, weight, dimensions, location and timing; compression ratios; ignition requirements; and the location and means for operating camshafts and other valve-actuating mechanism. Data are given regarding the best material and dimensions for pistons and the desirable number of rings. The physical characteristics of alloy steel desirable for use in connecting-rods are mentioned. Similar data, including dimensions and factors controlling the construction of the crankshaft and its bearings are included. The relation of the inertia stresses set up by reciprocating parts to those due to the explosion and compression pressure on the piston head is indicated, and the maximum total stress deduced.

The author states that the purpose of the paper is to outline that phase of metallurgical work pertaining to the connection between the laboratory and production in the automotive industry. Reasons are cited for selecting certain designs for parts to facilitate machining, complete or partial case-hardening, finishing and assembling. The next step is the choice of materials, a subject which is treated at some length. The author then takes up in turn the field for standardization in steel specifications, inspection of materials, physical testing of steels, uniformity of composition of metals, heat-treating operations, methods of carburizing, depths of case-hardening, treatment after carburization, errors in overspeeding hardening operations and drawing heat-treatment at low temperatures. Types of pyrometers, operations on hardened work, inspection for hardness and selection of hardening equipment are some of the other topics discussed.

Inasmuch as horses cannot meet the demand for increased farm power, the tractor must come at once. So far the supply of tractors has been entirely inadequate to meet the demand. The author specifiies some of the problems that confront designers of farm tractors. To make the tractor immediately available for farm work, it must be adaptable to practically all of the existing types of horse-drawn implements, besides furnishing belt power for a wide variety of present power-driven farm machinery. In designing tractors it must be remembered that the horse is a very flexible unit, capable of a wide variation in power output. Designing a tractor to furnish the necessary power for the majority of farm conditions, requires an intimate knowledge of crops, soils and farm management. These must be analyzed carefully so as to make the machine have as wide a range of usefulness as possible.

The author limits his consideration of rear axles to that of the bevel-gear type and takes up the subject under the heads of load-carrying member, gearing, driving-shaft, brakes and materials. Several different forms of cast and pressed axle housings are briefly described. Mention is then made of the axle gearing and data given showing the end thrust for straight-tooth bevel pinions. The methods of supporting pinions and of attaching bevel gears to the differential are discussed. Forms of differentials are considered, several different conventional types being illustrated. The subject of driving shafts is briefly reviewed, as is also that of brakes and brake materials. The author concludes his paper by figures showing the tensile strength, elastic limit and elongation of the metals used in the various parts of the rear axle and also explains some oil-retaining and dust-protecting features of design.

The author considers the effects of velocity variation on the operation of a car and states that this variation is absorbed mainly by the flywheel. A formula is given for calculating the pressure on universal bearings. Various methods of protecting and lubricating joints are described. A number of European types of joints are illustrated. A much larger number of types of joints are used abroad in-asmuch as each maker usually makes his own design instead of purchasing it from a specialist as is the usual practice in this country. In conclusion the paper describes types of joints using flexible material, such as leather or spring steel.

In this paper the author gives the results of an investigation of coarse crystallization. This investigation was carried out with commercial materials such as cold-drawn wire, hot and cold-rolled sheet, strip steel, cold-drawn tube and cold-pressings. The results of other investigations are briefly outlined. Coarse crystallization, or grain-growth, it is stated, is due to the action of a limited amount of strain, exceeding the elastic limit, followed by annealing within certain temperature ranges. The experimental work which led to this conclusion is explained in detail in the paper. The effect of forging, cold-drawing, cold-rolling and cold-pressing was determined with commercial materials. Some study was made of the effect of carbon on grain-growth and of the effect of coarse crystallization on the physical properties. In the discussion of commercial materials special reference is made to those used in motor car construction.